| BUILDER |
WORKING DEVICES |
HOW |
TP-IDE |
CBIOS |
| Andrew Lynch |
Seagate ST51270A IDE hard drive |
Drive has NONE of the configuration jumpers set -- puts the drive in "single drive mode". I also used a 40 pin IDE cable with the motherboard connector on the controller and the far end connector on the hard drive. I had to remove R1, R2, and R3 to get the Disk IO board to work with the drive. All logic is 74LSxxx.
|
YES |
YES |
| Max Scane |
Sandisk 512 MB Compact Flash drive and IDE adapter |
Adapter configured as Master. Drive worked with R1, R2, R3 installed but now removed and still working. Standard 40 pin ribbon cable. All logic is 74HC |
YES |
YES |
| Max Scane |
Quantum Lightning 340 MB IDE drive
|
Configured as master with resistors removed |
YES |
YES |
| |
|
|
|
|
| Rich Camarda |
Lexar 256MB Compact Flash and IDE adapter |
Adapter configured as Master. Works with resistors R1, R2, R3, removed or installed. |
YES |
YES |
| Rich Camarda |
Seagate ST3160815A IDE Hard Drive |
Replaced 74LS245 with 74F245, and replaced IC2 - 74LS373 with a 74F373. R1 installed (CSEL pulled HIGH) R2, & R3 removed. |
YES |
YES |
| Andrew Lynch |
Quantum ProDrive 270A |
(Master w/DASP DS) 40 pin IDE cable, R1, R2, R3 removed. |
YES |
YES |
| Andrew Lynch |
Maxtor 5T010H1 |
(Master JP50), 40 pin IDE cable, R1, R2, R3 removed. |
YES |
YES |
| Andrew Lynch |
Maxtor 71080AP |
(Master J20 only), 40 pin IDE cable, R1, R2, R3 removed. |
YES |
YES |
| Andrew Lynch |
Seagate ST315323A |
(Master, Single), 40 pin IDE cable, R1, R2, R3 removed. |
YES |
YES |
| |
|
|
|
|
| Rich Cini |
Toshiba 1.44GB Laptop drive |
R1 and R2 lifted and R3 pulled-up to Vcc. IC1-IC3 replaced with 74F equivalents. Cable length is 24". |
YES |
YES |
| Rich Cini |
IDE->CF adapter with 1gb SanDisk CF card |
R1 and R2 lifted and R3 pulled-up to Vcc. IC1-IC3 replaced with 74F equivalents. CF adapter connected directly to the Disk-I/O board (made for Micro-ITX motherboard). |
YES |
YES |
| Rich Cini |
Seagate ST51270A IDE hard drive |
R1 and R2 lifted and R3 pulled-up to Vcc. IC1-IC3 replaced with 74F equivalents. Cable length is 24". |
YES |
YES |
| Rolf Harrmann |
IDE HD Conner CFS1275A
|
R1, R2, R3 removed.
|
YES |
YES |
| Rolf Harrmann |
Seagate ST51270A
|
|
YES |
YES |
| Rolf Harrmann |
Seagate ST31220A
|
|
YES |
YES |
| Rolf Harrman |
IDE->CF Adapter with Transcend CF 512 MB |
tested the with the R1, R2, R3 removed. IC1 74F245, IC2 74F373,IC3 74F373
|
YES |
YES |
|
|
|
|
|
|
| Ron Ward |
IBM Deskstar DTLA 307045 46.1 GB
|
Requires the "smart cable." All resistors are installed except R1 which has been replaced with a jumper wire, |
YES |
YES |
| Ron Ward |
IBM Travelstar DTLA 307045 4.86 GB |
Requires the "smart cable" AND a 3 1/2 inch adapter for laptop drives. All resistors are installed except R1 which has been replaced with a jumper wire, |
YES |
YES |
| Dan Werner |
MAXTOR DiamondMax Plus 8 30 GB |
tested with R1,R2,R3 removed (Master) |
YES |
YES |
| Dan Werner |
IOMEGA ZIP 100 & 250 ATAPI |
Tested with R1 R2 R3 removed - Utility program and CBIOS to follow (Master) |
no |
no |
| Dan Werner |
Lite-ON CDRW ltr-24102M |
Tested with R1 R2 R3 removed. Will respond to ATAPI Packets (Master) |
no |
no |
| Adam Tompkins |
Maxtor DiamondMax 91360D8 |
Standard 40-pin IDE cable, drive configured as master. DiskIO board in default configuration with R1, R2, R3 installed. All logic is 74LS. Formatted with FMTPART2.COM. |
YES |
YES |
| |
|
|
|
|
| Adam Tompkins |
Kodak 8MB CF with IDE Adapter |
CF<->IDE Adapter configured as master. DiskIO board in default configuration with R1, R2, R3 installed. All logic is 74LS. Formatted with FMTPART1.COM only works with Sep/09 or later BIOS. |
YES |
YES |
| Nik Brisevac |
WD Caviar WD400
40GB
|
R1,R2,R3 installed or removed. I/O brd default settings. Disk Sectors filled with E5 then Formatted with FMTPART2. All logic 74LS. Default romimage 23/05/08. |
YES |
YES |
Comments (0)
You don't have permission to comment on this page.